ASTM A335 alloy pipe

ASTM A335 seamless ferritic alloy-steel pipe for high-temperature service. The pipe shall be suitable for bending, flanging (vanstoning), and similar forming operations, and for fusion welding. Grade P2 and P12 steel pipes shall be made by coarse-grain melting practice.

Our products for ASTM A335 alloy steel pipes have been listed as follows:

ASTM A335 P11 alloy steel pipe

ASTM A335 P91 Alloy Seamless Steel Pipe

ASTM A335 Grade P22 Alloy pipes

ASTM A335 P5 Alloy Seamless Steel Pipes

ASTM A335 P9 Alloy Steel Pipes

ASTM A335 P92 Alloy Seamless Steel Pipe

The steel material shall conform to chemical composition, tensile property, and hardness requirements. Each length of pipe shall be subjected to the hydrostatic test. Also, each pipe shall be examined by a non-destructive examination method in accordance to the required practices. The range of pipe sizes that may be examined by each method shall be subjected to the limitations in the scope of the respective practices. The different mechanical test requirements for pipes, namely, transverse or longitudinal tension test, flattening test, and hardness or bend test are presented.

Mainly Grade of ASTM A335：

ASTM A335 P11, ASTM A335 P22, ASTM A335 P5, ASTM A335 P9, ASTM A335 P91, ASTM A335 P92

Chemical Composition (%) for the main grade

Grade	C	Mn	P, S, max	Si	Cr	Mo
P11	0.05-0.15	0.30-0.60	0.025	0.50-1.00	1.00-1.50	0.44-0.65
P22	0.05-0.15	0.30-0.60	0.025	0.50 max	1.90-2.60	0.87-1.13
P5	0.15 max	0.30-0.60	0.025	0.50 max	4.00-6.00	0.45-0.65
P9	0.15 max	0.30-0.60	0.025	0.25-1.00	8.00-10.00	0.90-1.10
P91	0.08-0.12	0.30-0.60	0.020/0.010	0.20-0.50	8.00-9.50	0.85-1.05
V 0.18-0.25	N 0.03-0.07	Ni 0.40 max	Al 0.02 max	Nb 0.06-0.10	Ti 0.01 max
P92	0.07-0.13	0.30-0.60	0.020/0.010	0.50 max	8.50-9.50	0.30-0.60
V 0.15-0.25	N 0.03-0.07	Ni 0.40 max	Al 0.02 max	Nb 0.04-0.09	W 1.50-2.00
B 0.001-0.006	Ti 0.01 max	Zr 0.01 max

Mechanical Properties

Grade P11, P22, P5, P9	Grade P91	Grade P92
Tensile strength, min, (MPa)	415	585	620
Yield strength, min, (MPa)	205	415	440
Elongation, min, (%), L/T	30/20	20/…	20/…

Heat Treatment

A / N+T

N+T / Q+T

N+T

Material & Manufacture

Pipe may be either hot finished or cold drawn with the finishing heat treatment noted below.

此博客中的热门博文

Silicon carbide alloy ceramic wear tube

Reaction bonded SiC is made by infiltrating compacts made of mixtures of SiC and carbon with liquid silicon. The silicon reacts with the carbon forming more SiC which bonds the initial SiC particles. Silicon carbide is formed in two ways, reaction bonding and sintering. Each forming method greatly affects the end microstructure. Reaction bonded SiC is made by infiltrating compacts made of mixtures of SiC and carbon with liquid silicon. The silicon reacts with the carbon forming more SiC which bonds the initial SiC particles. Sintered SiC is produced from pure SiC powder with non-oxide sintering aids. Conventional ceramic forming processes are used and the material is sintered in an inert atmosphere at temperatures up to 2000ºC or higher. Both forms of silicon carbide (SiC) are highly wear resistant with good mechanical properties, including high temperature strength and thermal shock resistance. Our engineers are always available to best advise you on the strengths and weaknesses of ea...

阅读全文

ASTM A335 P9 Alloy Steel Pipes

ASTM A335 P9 Alloy Steel Pipes alloy steel , Alloy steel pipe , ASTM A335 , ASTM A335 p9 , Steel pipe , steel pipes ASTM A335 P9 is the part of ASTM A335, The pipe shall be suitable for bending, flanging, and similar forming operations, and for fusion welding. The steel material shall conform to chemical composition, tensile property, and hardness requirements. Each length of pipe shall be subjected to the hydrostatic test. Also, each pipe shall be examined by a non-destructive examination method in accordance to the required practices. The different mechanical test requirements for pipes, namely, transverse or longitudinal tension test, flattening test, and hardness or bend test are presented.Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested. Material & Manufacture Pipe may be either hot finished or cold drawn with the finishing heat treatment noted below. Heat Treatment A / N+T N+T / Q+T N+T ...

阅读全文

Ultra high molecular weight polyethylene pipe

Ultra-high molecular weight polyethylene (UHMW-PE) is a new kind of engineering thermoplastics with more than 3 million viscosity-average molecular weight. What is UHMWPE Ultra-high molecular weight polyethylene pipe has superior performance over conventional HDPE pipe such as very high wear resistance, impact resistance, excellent resistance to internal pressure strength, resistance to environmental stress cracking, intrinsically self-lubricating, anti-adhesion, low temperature resistance and excellent chemical resistance. UHMWPE wear pipe UHMWPE pipe bend UHMWPE pipe for dredginge UHMWPE pipe with flangee Ultra-high molecular weight polyethylene (UHMW full name is ultra-high molecular weight polyethylene pipe) is a thermoplastic engineering plastics with an average molecular weight greater than 1.5 million, which is polymerized by ethylene and butadiene monomer under the action of a catalyst. Ultra high molecular weight polyethylene is superior in comprehensive performance, abrasion ...

阅读全文