跳至主要内容

陶瓷管道安装施工中的安全要点

管道安装施工,安全问题十分突出,应该采用有力措施保证安全施工,现将要点列于 下面。
①在陶瓷管道安装时,为便于陶瓷管道安装施工方便,需适当设置脚手架等安全设施。
②在结构吊装时,为防止人员、物料和工具坠落或飞出造成安全事故,需铺设安全网。 安全网根据使用性能分为安全平网和安全竖网。
③为便于陶瓷管道安装施工,在陶瓷管道阀门等部位按规定要设操作平台。
④陶瓷管道安装施工需要许多设备,如电焊机、空压机、氧气瓶、乙炔瓶等,这些设备的 使用必须严格按安全操作规程执行。
⑤施工用的电动机械和设备均需接地,绝对不允许使用破损的导线和电缆,严防设备漏电。施工用电气设备和机械的电缆,必须集中在一起,并分别设置配电箱。
⑥髙空施工作业时,作业人员必须按规定进行“三宝”和“四口”防护。
⑦安装施工时还应注意防火,提供必要的灭火设备和消防人员。
⑧安装施工应认真执行安装方案。特别是安全操作要求。

此博客中的热门博文

ASME SA210C stocks

ASME  SA 210 Grade C  Tubes  

Bi Metal Clad bend

Bimetal Clad Pipe Bend are cast with mold vanishing vacuum suction casting cladding process. Outer of straight pipe is common steel pipe, cladding realized by forming high chromium lining via centrifugal forming technique. 1. Manufacturing Process of Bimetal Clad Pipe and Bend: Bimetal Clad Pipe and Bend are cast with mold vanishing vacuum suction casting cladding process. Outer of straight pipe is common steel pipe, cladding realized by forming high chromium lining via centrifugal forming technique. Outer of bend uses hot-bending bend and lining is cast with high-chromium cast iron. Bends and other profile sections can be cladded in whole and this process has changed the traditional practice to fabricate bend and other profile sections by drawing polyline without changing flow pattern of material inside piping,greatly reducing conveyance resistance of material. 2. Advantages Compared with Traditional Wear Resistant Alloy Cast Iron, Alloy Cast Steel, General Clad Steel Pipe and Cast St...

ASTM A335 P5 Alloy Seamless Steel Pipes

ASTM A335 P5 Alloy Seamless Steel Pipes ASTM A335 ,  ASTM A335 P5 ,  ASTM A335 P5 alloy pipe ,  seamless steel pipes ,  steel pipes Each length of pipe shall be subjected to the hydrostatic test. Also, each pipe shall be examined by a non-destructive examination method in accordance to the required practices. The different mechanical test requirements for pipes, namely, transverse or longitudinal tension test, flattening test, and hardness or bend test are presented.Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested. Material & Manufacture Pipe may be either hot finished or cold drawn with the finishing heat treatment noted below. Heat Treatment A / N+T N+T / Q+T N+T Mechanical Tests Specified Transverse or Longitudinal Tension Test and Flattening Test, Hardness Test, or Bend Test For material heat treated in a batch-type furnace, tests shall be made on 5% of the pipe from each treated lot. For small lots...