跳至主要内容

Other Structural steel pipe


 Structural Tubing is for high stress structural application like bridges, buildings, roll cages, and underwater platforms with wall thickness from 3/16" and up. It is often referred to as Hollow Structural Sections or just the acronym HSS.

Production Range

  • OD: 42mm-760mm
  • WT: 4mm-120mm

Standard and Steel Grade

  • GB/T 8162
  • GB/T 17396 or technical agreement.
UsageOD(mm)WT(mm)Steel GradeStandard/ SpecificationAplication Fields 
Structural Pipe42-7604-12020#,35#,45#,Q345A/B/C/D,Q390, Q420,25Mn,27SiMn etc.GB/T 8162General structural and mechanical pipe
Vehicle Pipe45-2454-3520Mn2,SAE1527,MZ410R, MZ530R,30Mn2,40Cr,45Mn2 etc.Technical agreement, YB/T5035Pipe used for automobile axle and automobile semi-shaft
Mold Pipe &TubeDN200-DN1200　21CrMo10,21CrMo10-2 etc.Q/OHAD030, technical agreementCentrifugal graphite casting-iron pipe mold
Military Pipe42-7604-12030Cr,40Cr,35CrNi1MoA etc.National military standard, agreementPipe for military use
Geology Drilling Pipe &Tube42-1334-25DZ40,DZ55,STM-R780,DZ60 etc.Q/OHAD006, GB/T 9808, agreementDrilling pipe
Hydraulic Support Pipe42-7604-12020#,35#,45#,27SiMn,30MnNbRE, 30CrMnSi,30CrMnSiA etc.GB/T 17396, technical agreementMaking hydraulic equipment for coal mine exploitation and hydraulic cylinder and piston for truck crane
Fluid Transmission Pipe & Tube42-7604-12020#,Q345,Q390 etc.GB/T 8163, technical agreementPipe & tube used for fluid transmission

Note: Steel pipe can be developed and produced to meet the users’ personalized requirements according to their demands.

此博客中的热门博文

ASTM A213 T11 Seamless tube

ASTM A213 ,  ASTM A213 T11 ,  boiler tube ,  Heat exchanger tube ,  heat exchanger tubes ,  steel tubes ,  Tubing ASTM A213 T11 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T11 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched i
阅读全文

Pipe for cryogenic device

  Cryogenic piping refers to systems that are used in a wide range of industrial applications that require extremely low temperatures, generally around -300°F (150°C) or lower. Due to such low temperatures, cryogenic pipes face unique corrosion and deterioration challenges. Cyrogenic piping is also referred to as cold piping. Implement specifications such as ASME SA-333M, GB/T18984. The seamless steel tubes are applied for low temperature pressure vessel pipeline and low temperature heat exchanger pipeline. Usage Specification Steel Grade Seamless and Welding Nominal Pipe used for Low Temperature ASME SA -333M Gr.3, Gr.6, Gr.8 and so on Seamless Steel Pipe used for Low Temperature Pipeline GB/T18984 16MnDG, 06Ni3MoDG, 06Ni9MoDG and so on ASTM A333 (ASME S/A-333) Pipe grades permit low temperature service.  Mechanical requiremnts of ASTM A333 alloy pipe Grade Tensile Strength (MPa） Yield Point (MPa) Elongation (%) Y X Grade 3 ≥450 ≥240 ≥30 ≥20 Grade 6 ≥415 ≥240 ≥30 ≥16.5 Grade 8 ≥690 ≥5
阅读全文

Ceramic Lining Pipe and Elbow

Ceramic Lining Pipe and Elbow have very uniform coating of specially formulated ceramic material that is affixed to the inner of the pipe and gives a very smooth surface. Ceramics with very low friction factor at low impingement angles decreases the abrasion of materials maximally. Its low density makes it easy to carry and install. Furthermore, its diamond-like hardness, fine grain structure and superior mechanical strength are the unique features that make it a wide range of demanding applications, such as coal preparation, power generation, iron and steelmaking, cement, asphalt, dredging, mining and mineral processing, oil and gas drilling. Metals have good ductility but poor resistance to abrasion - which means that abrasion prevention is required when metal pipes are used in high-temperature fluid catalyst service. On the other hand, ceramics possess great hardness and abrasion resistance, but they are brittle. Metal Ceramic double pipe is a hybrid pipe using metal as an outer pip
阅读全文